Initiatives/LEED
MoistureBloc
Today’s fast-paced construction demands products that are easy to use while effectively preventing and solving concrete slab moisture issues. With MoistureBloc products, floor covering can be economically installed without costly delays. MoistureBloc will remediate moisture vapor and pH issues on existing floors and properly cure new/fresh concrete, preventing flooring failures due to moisture vapor emissions as high as 27 pounds. Three easy steps to prevent or solve moisture vapor .problems.
VOC Water Base
MoistureBloc Emulsion One Step
One coat application, minimal odor, very low per square foot cost, reduces moisture vapor readings ranging from 9 to under 3 lbs. Adhesive ready in 12 hours.
MoistureBloc Emulsion Vapor Reduction System
Easy two step application, minimal odor, reduces moisture vapor readings ranging from 15 to under 3lbs. Cost effective and can be used with reactive and non reactive adhesives.
Technical Note
Job Survey
Data Sheet-MB Emulsion Re-Active Step 3
Data Sheet-MB Emulsion Primer Step 1
MSDS-MoistureBloc Emulsion Primer
Data Sheet-MB Emulsion Top Coat Step 2
MSDS-MoistureBloc Emulsion® Top Coat
MSDS-MoistureBloc® Emulsion Re-Active
Warranty
MoistureBloc® Brochure
Technical Note - Adhesives
MoistureBloc Universal
One coat application, minimal odor, adhesive can be applied after 12 hours, reduces moisture vapor readings ranging from 8 to under 3 lbs. Can be used interior and exterior with reactive and non reactive adhesives. Meets all California VOC regulations and LEED point standards.
VOC Solvent Base
MoistureBloc Stripper
An eco-friendly heavy bodied stripper designed for the cleaning and removal of coatings and other residues from concrete surfaces. MoistureBloc Stripper will effectively and safely remove paints, varnishes, urethanes, epoxies, sealers, acrylics, floor waxes and curing compounds from concrete floors receiving MoistureBloc products.
MoistureBloc Floor Cleaner
An eco-friendly all natural industrial surface preparation cleaner. MoistureBloc Floor Cleaner will effectively and safely clean grease and oil stains, tire marks and dirt from concrete floors receiving MoistureBloc products.
MoistureBloc Vapor Reduction FT System
Easy two step fast track installation, start laying floor in 18 hours, reduces moisture vapor readings ranging from 15 to under 3 lbs. Can be used with reactive and non reactive adhesives.
Job Survey
Data Sheet-MB Top Coat Step 2
MSDS-MoistureBloc Top Coat FT Step 2
Data Sheet-MoistureBloc Primer FT Step 1
MSDS-MoistureBloc Primer FT Step 1
Data Sheet-MB Re-Active Step 3
MSDS-MoistureBloc Re-Active FT Step 3
Warranty
Test Report-Adhesion,Impact Resistance,Flexibility
MoistureBloc® Brochure
Technical Note - Adhesives
MoistureBloc Vapor Reduction FT System AIM
Low VOC easy two step fast track installation, start laying floor in 18 hours, reduces moisture vapor readings ranging from 15 to under 3 lbs. Can be used with reactive and non reactive adhesives.
Data Sheet-MB Primer Step 1
Data Sheet-MoistureBloc Top Coat FT Step 2
MSDS - MoistureBloc Top Coat FT Step 2
Data Sheet-MoistureBloc Re-Active FT Step 3
MSDS - MoistureBloc Re-Active FT Step 3
MSDS-MoistureBloc Primer FT Step 1
Warranty
Test Report-Adhesion,Impact Resistance,Flexibility
Job Survey
Technical Note - Adhesives
MoistureBloc MX
Maximum protection against flooring adhesive failure caused from moisture vapor in concrete. Guaranteed to reduce 27/# calcium chloride test to below 3.0#/ 1000 sq. ft./24hrs. Promotes resistance to mildew, algae and bacteria.
MoistureBloc MX AIM
Low VOC maximum protection against flooring adhesive failure caused from moisture vapor in concrete. Guaranteed to reduce 27/# calcium chloride test to below 3.0#/ 1000 sq. ft./24hrs. Promotes resistance to mildew, algae and bacteria.
MoistureBloc Primer MX
Advanced curing and sealing primer used exclusively with MoistureBloc MX. Apply to new concrete for fast track installation or existing concrete.
MoistureBloc Primer MX AIM
Low VOC advanced curing and sealing primer used exclusively with Moisturebloc MX. Apply to new concrete for fast track installation or existing concrete.
MoistureBloc Patch
A self curing advanced polymer modified high strength leveling compound for patching and restoration of interior MoistureBloc treated concrete floor surfaces. It provides excellent bonding, flexural and tensile strengths as well as excellent water resistance due to its low permeability.
MoistureBloc Adhesive Remover
Strips adhesives from concrete floors and other concrete surfaces with relative ease. Removes many types of adhesives from concrete such as, cut back, latex and pressure sensitive. The product will also clean oil stains from concrete.
MoistureBloc Flexible Joint Sealant
A breathable two-part epoxy flexible joint filler designed for use on MoistureBloc treated surfaces that require fast-track filling and sealing of moving expansion/ contraction joints.
MoistureBloc Surface Bond
Improves the bond between a MoistureBloc treated surface and leveling and patching compounds such as MoistureBloc SLU and MoistureBloc Patch. The product comes ready to use and can be re-emulsified when cement topping application is delayed.
MoistureBloc SLU
A high strength and fast setting single component self leveling underlayment designed to level and smooth interior MoistureBloc treated substrates prior to installation of finished flooring.
VOC Not Required
MoistureBloc FP
Advanced polymer modified cement for the patching and restoration of concrete floors which are not subjected to concentrated of point loading. Similar to concrete in color, is ideal for leaving floors prior to floor covering installations.
